Entering an intermediate stop

Introduction

When route guidance is active, you can enter an intermediate stop. Intermediate stops can be predefined destinations from the following categories that COMAND offers for selection:

Mercedes-Benz Service Center
Hospital
Gas Station
Parking Lot
Restaurant

However, you can also enter destinations other than the predefined ones. To do this select the menu item Other.

You can use the intermediate stop function to influence route guidance to the main destination. When you have reached your intermediate stop, COMAND automatically recalculates the route to the main destination.

Entering predefined destinations

To activate navigation mode: press the function button once or twice. function button once or twice.

the COMAND To show the menu: press the COMAND the COMAND controller.

system menu bar by turning Select Destination in the navigation system menu bar by turning the the COMAND controller and pressing confirm. to confirm.

to confirm. Select Stopover and press to confirm. to confirm.

Option 1: no intermediate stop has been entered yet.

Option 2: an intermediate stop has Select a category; see option 2.

Option 2: an intermediate stop has already been entered.

to Select Change Stopover and press to to confirm.

turning To select a category: select a category by turning the COMAND controller and the COMAND controller and pressing COMAND first searches in the selected to confirm.

COMAND first searches in the selected category for destinations along the route.

If there are no destinations available there, COMAND searches for destinations within a radius of up to 100 km of the vehicle position.

If COMAND finds destinations, a list appears on the right-hand side of the display. The currently selected point of interest is highlighted on the left-hand side of the map.

The intermediate stops are listed according to increasing distance from the current vehicle position. They are displayed in the form of a name and their position in relation to the route and your direction of travel.

If COMAND does not find any destinations, you will see a message to this effect.

Select a different category. Confirm OK by pressing Select a different category..

Select the intermediate stop by turning Select a different category.

Select the intermediate stop by turning the COMAND controller and pressing the COMAND controller and pressing To start route calculation: select Start to confirm.

and press  to confirm. To start route calculation: select Start and press Entering another destination as an to confirm.

Entering another destination as an intermediate stop

To activate navigation mode: press the function button once or twice. function button once or twice.

the COMAND To show the menu: press the COMAND the COMAND controller.

system menu bar by turning Select Destination in the navigation system menu bar by turning the the COMAND controller and pressing confirm. to confirm.

to confirm. Select Stopover and press to confirm. to confirm.

confirm. Select Other and press confirm. to confirm.

From Last Destinations or From POIs. Select Address Entry, From Memory, From Last Destinations or From POIs.

Selection Step
Address Entry Enter a destination by address
From Memory Select a destination from the destination memory
From Last Destinations destinations Select a destination from the list of last destinations
From POIs Enter a point of interest

entered a destination, select Start and To start route calculation: once you have entered a destination, select Start and press Deleting an intermediate stop to confirm.

Deleting an intermediate stop

If an intermediate stop has already been entered, you can delete it.

To activate navigation mode: press the function button once or twice. function button once or twice.

the COMAND To show the menu: press the COMAND the COMAND controller.

system menu bar by turning Select Destination in the navigation system menu bar by turning the the COMAND controller and pressing confirm. to confirm.

to confirm. Select Stopover and press to confirm. to confirm.

to Select Delete Stopover and press to to confirm.

COMAND deletes the intermediate stop and recalculates the route to the main destination.

    See also:

    Muscular Moves, Eventually
    The turbo-diesel GL320 Bluetec has additional exhaust treatments to cut soot and nitrogen oxide emissions — technology last year's diesel GL320 CDI lacked, which is why California and several Nort ...

    EBD (electronic brake force distribution)
    Observe the "Important safety notes" section EBD monitors and controls the brake pressure on the rear wheels to improve driving stability while braking. WARNING If EBD has malfu ...

    Stowage well under the trunk floor (Sedan)
    The TIREFIT kit, the vehicle tool kit, etc. are located in the stowage compartment. •► To open: pull handle 1 upwards •► Hook handle 1 into rain trough 2. ! Unhook the handle befo ...